AstroStart RS-623 Installation Manual. Download Installation manual of AstroStart RS-711XR Remote Starter for Free or View it Online on All-Guides.com.
Download Installation manual of AstroStart RS-711XR Remote Starter for Free or View it Online on All-Guides.com.
Brand: AstroStart
Category: Remote Starter
Type: Installation manual
Model: AstroStart RS-711XR , AstroStart RS-623
Pages: 2
INSTALLATION MANUAL
MODELS RS-623
FOR ALL
GAS- AND
AUTOMOBILES
QUALIFIED PERSONNEL.
WITH MANUAL TRANSMISSION, THE INSTALLATION
A MANUAL INTERFACE
188 ST-FRANÇOIS XAVIER
MORE DETAILED INFORMATION CAN BE FOUND IN THE
WWW.ASTROFLEX.COM/DEALER
ISBRS711 07 07
The control module in this kit
the type of vehicle on which it is to be used.
programming: see programming level 16.
before proceeding with installation!
INSTALLATION ON VEHICLE
WITH AUTOMATIC TRANSMISSION:
When set to “Automatic” mode, the control
![Download free astrostart for manual transmission problems Download free astrostart for manual transmission problems](http://remote-starter.getusermanual.com/images/user-s-manual/1105u/1.gif)
into account when remote starting, as this
function is factory-installed on most new vehicles.
To ensure safe installation of
1.Ensure that vehicle cannot be remote started while in
2.Also ensure that gearshift lever cannot be moved out of
If engine can be started while transmission is in
gear or gearshift lever can be moved out of “Park”
position without depressing brake pedal, call our
APPROPRIATE, SAFE SOLUTION FOR THE MAKE
INSTALLATION ON VEHICLE
WITH MANUAL TRANSMISSION:
module does not take gearshift lever
It is designed to require the user to ensure
enable reception of a start command.
![Free Free](/uploads/1/2/5/6/125691201/553789780.jpg)
this product, check the following:
3.Ensure that all vehicle door pinswitchs are operational
immobilizing vehicle).
4. When installation is complete, check the doors and the
hatchback (by opening each one individually) to ensure
that opening any of them interrupts the safety sequence
which allows the system to perform a remote start.
5.Ensure that it is impossible to access the vehicle
gearshift lever without opening a door or the hatchback.
For convertible vehicles, it is strongly recommended
to add a (microwave) motion detector to prevent remote
start if activity is detected near the gearshift lever.
7.Be sure to affix the two warning stickers in the appropriate
•the smaller one must be visible on the driver’s side
•the other must be affixed near the hood latch.
8.Be sure to hang the “For your safety” card from rear-view
If gearshift lever can be accessed without opening any
door, or if any door (no matter which one) can be opened
without interrupting the safety sequence, call our Technical
APPROPRIATE, SAFE SOLUTION FOR THE MAKE
Code
1 Engine stop signal sent by remote control / pulse input.
2 Engine stop signal sent by depressing brake pedal.
No tach reading (RPM).
Note: If the engine is not running during a start cycle, it is
normal for no tach signal to be generated. This situation
may arise if the vehicle is equipped with an immoblilization
system (anti-theft); ensure that any such system is suitably
5 Hood open.
6 Engine stop signal sent by manual interface (invalid sequence).
8 Main switch “OFF”.
10
Note: If the engine starts and then suddenly stops during a
immobilization system (anti-theft); ensure that any such
11 Tach signal already detected during start attempt.
RPM above 3400. Note: May be due to number of cylinders
13
RPM below idle speed. Note: May be due to number of
14 Safety sequence interrupted by parking brake.
15 Safety sequence interrupted by door being opened.
17 Module programmed via receiver connector (MultiTest II).
Power supply below 8VDC or above 15VDC or system
19
Manual interface incorrectly connected to remote start
20 Set to “Manual Transmission” mode by system.
SAFETY SEQUENCE NOT ACCEPTED
If the control module refuses to validate the safety sequence, note
that the code must be read before the brakes are applied or a start
command is emitted, as these actions will replace the existing code
by a code “6” and you will have no indication of the reason for the
If no code is generated, the manual interface may be the cause for
•A door was open.
•The engine was not running at the time of the sequence (no
power to ignition or no tachometer signal detected).